On the home straight...

...So, I've go all the bits and pieces delivered and now to start the puzzle. 

First I have fitted the brakes. They are the calliper style with the cable pull on the side.

The only issue I have is the bolt on the rear is a bit short. Need to think about this one!

Next I have fitted the Brake levers to the bullhorn handle bars. The levers are like the time trial type. These fit in the open end of the bars as opposed to clamping around the bar.

The cable fits in the end of the lever and then the outer sleeve fits into the bottom of the lever housing. The black tape is holding the outer sleeve in place so I can get an idea of where it'll run. 
And yes it is orange!

And there's more......

You know how it is. Nothing for ages and then two posts in two days!

So not only have I fitted the wheels, tyres, and crank I have put the stem and handle bars on!

They are lacking bar tape. And brakes, but you get the idea.

 It was a bit of a faff to fit the handle bars to the stem. I had to open the stem up a bit to get the bars through.Just a quick tweak with a flat blade screwdriver to open the clamp up a bit to get the corner through and its done!

The tyres are Schwalbe delta cruiser. They have a puncture resistant design which I suspect I will test to the limit! 

Next will be the brakes. I will need to get the right ones as I have a large drop. Woof! This is the gap between the mounting hole in the bridge and the centre of the wheel rim. The rear brake needs to have a drop of around 73 mm which is quite a lot. I suspect this is because I have a 26" wheel in a frame which would have taken a 27". I know I can get the correct brakes from the joy that is Ebay!

So next pay day....! 

Catching up......

It's been a while since the last post so, in answer to the literally zero requests for update here we go.
Since the last payday I have fitted the bottom bracket, front and rear tubes and tyres.

The bottom bracket was a challenge to say the least! The unit itself is a good bit of kit. Its designed to fit into a bottom bracket shell with damages threads so its perfect for older bikes with older raleigh style cup and cone bottom brackets.

This is it fitted hand tight. As you can see the shaft is longer on one side which if it was fitted to a 68 mm is not a problem. As the shell on this frame is 71 mm it means that there is a slight difference in length between the left and right hand side of the shaft. This is because the bottom bracket tightens up on one side only so the fixed side stays the same length while the other side slowly emerges as it is tightens. Basically I had to install it the wrong way around to ensure the crank and crank arm didn't catch on the outside of it.  

 

Pay day at last!!!!!

At last pay day is here!
 I have ordered the Velo Orange grand cru threadless bottom bracket.
Sounds like a luxury item no cyclist can do without.
I have also sneaked a couple of Schwalbe Delta cruiser 26 x 1 3/8" tyres with amber side walls no less!  AND two inner tubes to match. Such extravagance....
Still a long way to go before its complete though. So, to keep my spirits up and plant a few seeds in a few minds, I have been looking at a some bespoke frame builders. 

Since the demise of the British cycle industry coupled with the fact you can walk into a shop and pick up a nondescript bike for a couple of hundred pounds and ride it home, cycling, in my humble opinion, got a bit boring! Over the past few years the spirit of the British back room engineers that developed things like the jet engine and the Blue Streak missile has been flourishing in sheds and workshops around the country.
One of these is feathercycles based in Yorkshire. 
The best bit of the website for me is the short video which shows Ricky Feather working in what looks like a shed in his back garden and turning out some fantastic looking cycles.
Another is Donhou bicycles. These guys made a bike from scratch to have a go at the cycle land speed record! The crank has 104 teeth! Have a look on the website and watch the Experiments in Speed video.




There is a massive movement now for hand built bespoke frames. There are also a few courses available to learn how to build frames. There's a show, Bespoked, for just such beauties.  

So I've found a supplier of frame building parts based in Kent. All I need is a workshop and a gas torch and I'm off! Maybe one day.....Eh Dar (you know who you are)!  

Mock up...

Had a bit of a play with the crank today. I'm impatiently waiting for pay day to arrive so I can buy the bottom bracket, wishing my life away while staring at components on eBay! What has my life become?

I used the threaded bar to fix the crank onto the bike using washers and nuts. I have to have a fix every now an then to remind me of what I hope it will look like when it's finished.

Really happy with the crank. Its a sturmey Archer with 42 teeth. Just want to get it fitted now. Then I can go back to staring at more stuff to buy!

For forks sake!!

Its in......I managed to press the headset in today with a nifty gadget I made up. Not the hammer and lump of wood I was looking forward to using but a length of threaded bar I had sitting around the shed, as you do. This together with a couple of nuts and a few square washers.

This is the set up I used. Its a bit basic but it worked really well. the threaded bar runs through the tube and the bearing cups are fitted, a liberal amount of copperslip grease was applied. This will hopefully stop any rust forming in the long term. 

ACME head set press

Then two large washers were put on top of the cups and then a nut at each end. I then used a spanner to tighten the nuts up. The washers kept the baring cups straight so they went in a treat.





This is how it looks now.........


Very happy with it. After this I fitted the Front fork. This was a bit more of a challenge. There is another bearing cup the needs to sit on the bottom of the steerer tube. This is an interference fit and needs to pushed in. In order to do this I ended up having to heat up the bearing cup to make it expand a bit then use the ACME bearing press (pat pending!) to press it on. Once the bearings had been cleaned and greased up with a bit of lithium grease I managed to fit the fork too. Which was nice.

Assembled front end

After this, I used the threaded bar to mock up the bottom bracket by fixing the crank to the bike with a couple of washers and nuts. I then had a job to adjust the crank to match up the rear chain line by adding or removing extra washers. I managed to get it as close as possible and worked out I will need a bottom bracket with a 110 mm spindle! So come pay day that's what I'll get.

Cycle-logical change.....

....See what I did there! Anyway. I find myself looking at old bicycles that are chained up at various points around town and thinking what they may look like after a quick spruce up. Its getting a bit of an obsession! I'm thinking of sneaking around under cover of darkness and setting them free!
I've been trawling the internet for inspiration for the finished look of the bike which has resulted in me thinking about the next build already!

foffa bikes have the facility to build your bike on-line and choose the specification of the equipment and colours of even the tyres.

Pitango bikes is another bike building site where you can even choose what colour chain you want!

What I have been doing is looking at the equipment specifications on these bikes, bearing in mind they cost upwards of £350, and going onto e-bay and seeing if I can source them cheaper. For the most part its possible to get things like old style brake calipers for around £20, brake levers for around £17, its when you start looking into the individual components that the real cost starts to show itself. There are different prices for the same stuff! 
I like the bull horn style handlebars: These are £59.95
  
and these are £21.95
Its like everything else if you want to pay for a named brand then you can spend a fortune. If you want a similar look for cheaper its possible. Which is just as well for me!